Transair 6612 40 00 1-1/2" ID (40 mm) 45° Elbow Connector

Transair® fittings for aluminum pipe install fast and with minimal tooling. All Transair® fittings are designed to securely fit around Transair® aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair® fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum and industrial/inert gas systems. All Transair® components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The "full bore design of Transair® fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone-free and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker® Hannifin warrants all Transair® components to be free of defects in material and workmanship for 10 years from the date of installation. Transair® 1/2 in (16.5 mm), 1 in (25 mm) and 1-1/2 in (40 mm) fittings use push-to connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2 in, 1 in and 1-1/2 in pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair® marking tool. Transair® 2 in (50 mm) and 2-1/2 in (63 mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2 in and 2-1/2 in pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair® drill jig. Transair® 3 in (76 mm), 4 in (101 mm) and 6 in (168 mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3 in, 4 in and 6 in pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair® lugging tool and die.
Transair® 45 deg Pneumatic Elbow, 45 deg Elbow Fitting, 1-1/2 in Connection Size 1, Push-Fit Connection Type 1, 1-1/2 in Connection Size 2, Push-Fit Connection Type 2, Push-Fit|Push-Fit Connection, Fiberglass/Polymer, Fiberglass/Polyamide Material Construction, Black, 232 psi Maximum Operating Pressure, -4 to 185 deg F Operating, Additional Information: NBR Seal Material

• Quick-connection technology
• Modular and reusable
• Corrosion-resistant
• Full bore design
• Optimum flow rate
• 100% recyclable
• Faster installation
• Lower installation costs
• Immediate pressurization

• Catalog https://assets.unilogcorp.com/267/ITEM/DOC/Transair_6699_01_01_Catalog.pdf
• Instruction/Installation Manual https://assets.unilogcorp.com/267/ITEM/DOC/Transair_6650_00_00_04_Instruction_Installation_Manual.pdf
• Video Link https://videos.parker.com/vidad/publish.vidavee.com/publish/Parker/CD8FB56FE48623F30C2BD7C720A6461E.mp4